• Reduced volume of hazardous waste.
• Reduced solvent purchase, and disposal cost.
• Small generator status is available.
• Recycled solvent life is indefinite.
• No TSD permits required.
• Tax rebate available in Oklahoma.
• Units available to process up to 400 gallons/hour.

Solvent Recovery Systems sells and services the full line of NexGen and PRI products. We specialize in easy cleanout and/or liners. We can advise you in which unit will fit your needs as well as help in setup and training.

The following criteria for approval of the tax credit are taken from the Oklahoma DEQ website.

252:205-17-4. Criteria for approval of tax credit

To qualify for approval of a tax credit under this subchapter:

1. The tax credit must be taken within three years of the installation and initial use of the facility.
2. The proposed facility or equipment must have been previously demonstrated to be effective and to perform as specified unless unproven technology procedures are followed in accordance with 252:205-17-5.
3. The facility must be physically located in the State of Oklahoma.

Agency note: There is no minimum amount of a hazardous waste which must be recycled, reused or reduced.

• Acetone
• Alcohol
• Amyl Acetate
• Butyl Acetate
• Ethyl Acetate
• Ethylene Glycol Ethyl Ether
• Ethylene Glycol Ethyl Ether
• Isobutyl Acetate
• Isopropyl Alcohol
• Lacquer Diluents
• Methyl Alcohol (Methanol)
• Methyl Ethyl Ketone (MEK)
• Methyl Isobutyl Ketone (MIBK)
• Methylene Chloride
• Mineral Spirits
• Toluene (1-2-3)
• Toluol (Aromatic Hydrocarbon)
• Turpentine Gum
• Xylene (1-2-3)
• And many more

Our solvent recovery bags and liners meet or exceed all factory specifications, including dimensions, material thickness, and temperature and chemical resistance. Nylon and woven Teflon liners are available.

We can supply whatever quantity of solvent recovery liners or bags you need, whether you use your solvent recycling machine once a month, multiple times each day, or if you are a distributor or supplier. We can also set you up on an automatic delivery or reminder schedule to make ordering easier for you. Just call us at (479)439-0483 for pricing and availability.

As a distributor of Siva solvent distillation equipment (mfg ended in 2003) Solvent Recovery Systems has a knowledge base and parts inventory built up since 1984.

We can usually help troubleshoot problems on the phone and if a repair part is needed get it shipped with quick turnaround.

We can repair your circuit and logic boards, we also have new and used boards in stock.

New and used parts available:

• operations manuals
• lid gaskets
• circuit/logic boards
• heat transfer oil
• technical advice and troubleshooting
• nylon distilling bags, nylon and teflon flat liners
• heavy duty liners (formed bags, fiberglass/teflon)
• repair and service
• heating elements
• condensers
• Stainless steel solvent transfer hoses
• vacuum pumps

Siva and Recyclene Models

• R-2
• S-10(V)
• S-15
• S-30
• RS-20
• RS-35
• D-15
• D-35
• D-55
• M-60
• M-110

Contact us:

E-mail: mail@solventrecovery.com

Phone: (479)439-0483

Fax: (888)701-6180

Terms of sale for most machines:

• 50% down on order, 25% on shipping and 25% net 30 from delivery
• 6-month warranty on parts and labor (does not include travel)
• Freight on buyer
• Training/orientation for large machines (in the U.S.)

Units on hand (subject to change):

(2) Siva Disti D-35 Solvent Recovery Systems with vacuum
35 gallon unit with vacuum for distilling solvents with high boiling points

(2) Siva Recyclene R-2 Solvent Recovery Units
5 gallon unit with very user-friendly control

(1) Siva Recyclene R-2V Solvent Recovery Unit
5 gallon unit with vacuum for distilling solvents with high boiling points

(1) ADF Model 550 Glove-box Parts Washer
Hi pressure/low volume for hard-to-clean parts

(1) ADF Model 160 Rotating Basket Parts Washer
Hi pressure/low volume

(1) ADF Model 700 Rotating Basket Parts Washer
Low pressure/hi volume

We at Solvent Recovery Systems work with PRI to assess your needs so their engineers can design a machine custom-fit specifically for your application. PRI solvent recycling systems are supported by engineering, design, manufacturing, quality assurance, service, and after-the-sale support. PRI solvent recycling has contributed innovative solutions to environmental waste problems at both Fortune 500 clients and privately held companies.

How it Works

Solvent recycling is accomplished by a distillation process which includes the following steps:

• A still (distillation) vessel is charged with a waste solution on a batch or continuous basis.
• A thermal oil jacket, electrically or steam heated, injects heat into the waste solvent by conductive thermal transfer.
• The still may be operated under vacuum, which lowers the boiling temperature of the solvent.
• When the solvent reaches its reduced boiling point, the solvent changes from liquid to a vapor (gas) at a controlled rate.
• The solvent, in a vapor phase, passes through the condenser which has both a condensing and a subcooling section. In the condenser, the solvent changes back to a liquid and is cooled back to ambient conditions.
• The contaminants (solids or non-volatile liquids) do not undergo a vapor phase, but stay behind as “still bottoms” to be discharged out the drain port.

Once non-volatile portions build up to concentrated levels, the “still bottoms’ are discharged. Another production run can then be initiated.

Solvent recycling utilizes a solvent distillation unit to separate a process solvent from its contaminant for reuse. This process consists of heating the mixture until the solvent reaches its vaporization point. Once the solvent vaporizes, it enters a condenser unit where it is cooled back into liquid form leaving the contaminant behind. The volume of usable solvent from the waste solvent mixture will normally approach 99.9% and reach purity levels equal to virgin product.

Solvent recyclers are used in industries such as:

• Aerospace
• Automotive
• Boat Building
• Cabinet Manufacturers
• Defense Contractors
• Electronics
• Flexographic printing
• Furniture Manufacturers and Restorers
• Paint and Ink Manufacturers
• Petrochemicals
• Pharmaceutical
• Plastics and Composite Manufacturers

Solvent recycling uses a solvent distillation unit to process contaminated liquid solvents back to their original form, making them available for use again in the production processes. The process consists of heating the mixture until it vaporizes and then it is cooled back to liquid form, leaving the contaminant behind. A solvent recovery system presents many advantages to any business which uses one or more liquid solvents in their operations. One of the biggest advatages is the ability to purchase and store far less solvents on-site. Because these systems allow for recycling of contaminated materials with an output that is up to 99.9% pure, the solvents can be used indefinitely.

Disti’s customers include paint and ink manufacturers, chemical companies, printers, as well as, electronic, furniture, marine and automotive manufacturers and many other industries. Disti Kleen’s twenty-eight year history in the solvent recovery industry has given us a deep understanding of how to best help our customers save time, comply with EPA and OSHA regulations and most importantly, improve their bottom line. Our equipment is of the highest quality standards and latest technology. We have our own staff of factory trained technicians to provide start-up and operator training.